XDM280BT
INSTALLATION/OWNER'S MANUAL
AM/FM/CD Receiver
XDM280BT INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
•Remove trim ring from unit.
•Remove 2 transit screws located on top of the unit.
•Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
•Install mounting sleeve into opening, bending tabs to secure.
•Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
•Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
•Test for correct operation and slide into mounting sleeve to secure.
•Snap trim ring into place.
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
2
XDM280BT INSTALLATION
Wiring Diagram
Antenna
Connector
10 AMP
AGC Fuse
FUSE
When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could
damage the radio. The XDM280BT uses one 10 amp AGC fuse located beside the wiring connector.
3
XDM280BT OPERATION
Control Locations
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
20 | 19 | 18 | 17 | 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 |
1 | Release | 11 | Preset 5 | / Folder Down |
2 | Band / Go Back | 12 | Preset 4 | / Play / Pause |
3 | Power / Mute | 13 | Preset 3 | / Intro Preset 2 / |
4 | Bluetooth Talk | 14 Random Preset 1 / | ||
5 | Volume Knob | 15 | Repeat Display | |
6 | Audio / Menu | 16 | Mode | |
7 | Eject | 17 | Reset - (behind faceplate) | |
8 | USB Port | 18 | Tune / Track Up Tune / | |
9 | Auxiliary Input | 19 | Track Down | |
10 | Preset 6 / Folder Up | 20 |
4
XDM280BT OPERATION
Remote Control
1 2
3 | |||
17 | 4 | ||
5 | |||
16 | 6 | ||
15 | 7 | ||
14 | 8 | ||
13 | 9 | ||
12 | 10 | ||
11 | |||
1 | Mode | 10 | Preset 6 / Folder Up |
2 | Volume Up | 11 | Mute |
3 | Power | 12 | Audio / Menu |
4 | Select | 13 | Preset 5 / Folder Down |
5 | Tune / Track Up | 14 | Preset 4 / Play / Pause |
6 | Volume Down | 15 | Preset 1 / Repeat |
7 | Band / Go Back | 16 | Bluetooth Talk |
8 | Preset 3 / Intro | 17 Tune / Track Down |
9 Preset 2 / Random
5
XDM280BT OPERATION
General Operation
Power On/Off
Mode
Auxiliary Input
Volume
Display
Reset
Set the Clock
12/24-hour Clock
Setup Menu
Press or any other button (except EJECT) to turn the unit on. Press to turn the unit off.
Press MODE to select between AM/FM, CD player, Bluetooth, auxiliary and USB. Modes of operation are shown in the display.
NOTE: CD and USB modes will not appear unless a CD is inserted or USB device is connected.
The XDM280BT offers a 3.5 mm auxiliary input port on the front panel of the unit for connecting an audio device, MP3 player, etc. Press MODE to select auxiliary input mode.
Adjust volume using volume knob (00-46).
Press DISP to show the clock. During playback of MP3/files, ID3 tag information, elapsed time, track number and file/ folder names will automatically rotate on the display.
Press RESET upon initial installation or if abnormal operation occurs.
With the unit on, press and hold DISP until the clock begins to flash, then release. Press the arrow to the right to adjust the hours or the arrow to the left to adjust the minutes.
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00).
Press and hold AUDIO for more than 3 seconds to access the setup menu. Press AUDIO momentarily to select between the menu functions and rotate the volume knob left/right to adjust or activate the desired function.
6
XDM280BT OPERATION | ||||
General Operation - Setup Menu | ||||
Menu Function | Options | Action | ||
Auto Station | AUTO STORE | Press the volume knob to seek and save 6 strong stations in | ||
Store | the current band. (Tuner mode only) | |||
Local/Distance | LOCAL OFF | Activates distance tuning (Tuner mode only). | ||
LOCAL ON | Activates local tuning for strong station reception only (Tuner | |||
Tuning | ||||
mode only). | ||||
Tuner | FREQ USA | Programs the unit to USA tuner spacing. | ||
(200kHz for FM and 10kHz for AM). (Tuner mode only) | ||||
Frequency | ||||
Programs the unit to European tuner spacing. | ||||
Spacing | FREQ EURO | |||
(50kHz for FM and 9kHz for AM). (Tuner mode only) | ||||
Auxiliary Input | AUX ON | Enables the front panel 3.5mm auxiliary input. | ||
AUX OFF | Disables the front panel 3.5mm auxiliary input. | |||
Beep | BEEP OFF | Disables the confirmation beep. | ||
Confirmation | BEEP ON | Enables the confirmation beep. | ||
Programmable | PRO-VOL # | Programs unit to always turn on at a specific volume (default is | ||
Turn On Volume | OFF). Any volume level 1-30 can be selected. | |||
Power On | MSG OFF | Disables power on message. (Example: GOOD MORNING) | ||
Message | MSG ON | Enables power on message to be displayed. | ||
SCROLL 15 SP | Programs unit to scroll information every 15 seconds (default). | |||
Scrolling | SCROLL ONCE | Programs unit to scroll once then show the first 10 characters | ||
on display | ||||
Option | ||||
SCROLL ON | Programs unit to scroll continuously. | |||
SCROLL OFF | Programs the unit to show the first 10 characters on display. | |||
Demonstration | DEMO OFF | Disables the demonstration mode. | ||
Mode | DEMO ON | Enables the demonstration mode. | ||
Bluetooth | BT ON | Enables Bluetooth functionality. | ||
BT OFF | Disables Bluetooth functionality. | |||
ANSWER | Programs unit to automatically answer every incoming phone | |||
Auto Answer | Auto | call after 2-3 rings. | ||
ANSWER | Programs unit to require the | button must be pressed to | ||
Manual | answer incoming phone calls (default). | |||
7
XDM280BT OPERATION
General Operation
Audio Press AUDIO momentarily to select between Bass, Treble,
Balance and Fader.
BASS TREBLE BALANCE FADER EQ LOUD SOURCE LEVEL
Bass Press AUDIO until BASS appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).
Treble Press AUDIO until TREBLE appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).
Balance Press AUDIO until BAL appears then rotate volume knob left/right to adjust (BAL 12L - BAL 12R).
BAL EVEN represents equal balance
Fader Press AUDIO until FAD appears then rotate volume knob left/right to adjust (FAD 12R - FAD 12F).
FAD EVEN represents equal fader
8
Loading...